Skip to content
D&D
Translated from the Korean original. Read the original

Traction Machine RPM, Car Speed, Sheave Diameter and Roping Ratio

· 12 min read

  • Traction Machine rotational speed
  • Car speed
  • Sheave diameter
  • Roping ratio
  • 1:1 Roping
  • 2:1 Roping
  • Traction Machine specifications

Key points

  • Car speed varies even at the same Traction Machine rotational speed. A larger effective Sheave diameter increases rope travel speed, and the speed transmitted to the car varies with the Roping ratio.
  • 1:1 uses the rope speed directly, while 2:1 uses half of it. However, you must check that the notation matches the actual rope arrangement.
  • The calculation requires the effective diameter that determines rope travel. The Ø notation in a product listing must not immediately be taken as the diameter for calculation.
  • Rotational speed must be read with reference to the shaft on which the Sheave rotates. If there is a speed reduction relationship between the motor shaft and the Sheave shaft, account for it first.
  • Speed calculation is a starting point for comparing specifications. The calculation result alone cannot determine rated speed, replacement suitability or whether a speed change is possible.

⚠ CautionThis article explains general inspection criteria. For maintenance decisions on a specific installation, please also check that model’s manual and inspection criteria.

Contents▾
  1. 1.Why Traction Machine rotational speed alone cannot determine car speed
  2. 2.The calculation from rotational speed to car speed
  3. 3.How to apply 1:1 and 2:1 notation to speed calculations
  4. 4.Comparing diameter and Roping notation in our Traction Machine listings
  5. 5.Why the effective diameter for calculation must be checked separately
  6. 6.Read rotational speed together with the shaft and operating conditions
  7. 7.On site, follow the sequence from document checks to measured-value comparison
  8. 8.Limits when using calculation results to judge replacement or modification
  9. 9.Car speed requires diameter, Roping and rotational speed to be read together

Why Traction Machine rotational speed alone cannot determine car speed

Where rotary motion becomes linear motion

The Traction Machine rotates the Sheave, and the rope in contact with the Sheave moves with that rotation. To understand car speed, the relationship must be considered in two stages: from rotational speed to rope speed, and from rope speed to car speed.

The length of rope moved by one revolution of the Sheave is related to the circumference of the circle used in the calculation. Therefore, at the same rotational speed, a Sheave with a larger effective diameter moves a longer length of rope.

Next, examine the Roping arrangement. The distance traveled by the rope may equal the distance traveled by the car, or only part of the rope travel distance may appear as car movement.

Car speed is therefore not the result of rotational speed alone. Sheave shaft rotational speed, effective diameter and Roping ratio must be checked together to establish what the calculation means.

Establish the assumptions under which the calculation applies

The speed relationships explained in this article assume normal conditions in which the rope transmits the Sheave's motion as intended. These formulas do not guarantee actual speed while accounting for slippage or measurement errors.

Constant-speed travel must also be distinguished from acceleration and deceleration. Comparing a value calculated from rated rotational speed with car speed immediately after starting may cause a normal difference to be interpreted as an abnormality.

On site, first establish what is being compared. The information needed differs depending on whether the task is to examine the designed speed relationship or to identify the cause of a speed discrepancy during actual operation.

The calculation from rotational speed to car speed

First relate Sheave circumference to rotational speed

Let n be the Sheave shaft rotational speed and D be the effective diameter for calculation. The rope travel length corresponding to one revolution is π × D. Multiplying this by the rotational speed gives the length of rope traveling over the same period.

If n is in rpm and D is in m, rope speed can be expressed by the following relationship. Here, rpm means revolutions per minute.

Rope speed(m/s) = π × D × n ÷ 60

Divide by 60 to convert distance traveled per minute into distance traveled per second. If the diameter is read in mm, convert it to m before entering it. It is advisable to record both the diameter unit and the speed unit on the calculation sheet.

Apply the Roping ratio to obtain car speed

In this article, R is defined as rope travel speed divided by car travel speed. For conventional 1:1 Roping, R is taken as 1; for 2:1 Roping, R is taken as 2.

Car speed(m/s) = π × D × n ÷ (60 × R)

In this formula, n is the Sheave shaft rotational speed. Whether motor shaft rotational speed can be entered depends on the drive configuration, so first check which shaft the rotational speed in the specifications refers to.

Calculation element Meaning What to check before entering the value
n Sheave shaft revolutions per minute Check whether the value is for the motor shaft or the Sheave shaft.
D Effective diameter used to calculate rope travel Check whether it is the same as the outside diameter or the nominal designation in the listing.
R Ratio of rope speed to car speed Compare the actual rope arrangement with the Roping notation.
Calculation result Car speed assuming normal transmission of motion Establish whether it is being compared with a rated value or a measured value.

The units must be consistent and the meaning of each symbol clear before the calculation result can be reviewed. A calculation sheet containing only numbers is difficult for another person to reproduce under the same conditions.

How to apply 1:1 and 2:1 notation to speed calculations

In 1:1, rope travel corresponds to car travel

For conventional 1:1 Roping, speed is calculated on the basis that the car travels the same distance as the rope. The rope speed obtained at the Sheave is therefore used as the car speed.

This does not mean that every pulley along the rope path is included separately in the speed ratio. The role of a pulley that only changes the rope's direction at a fixed position must be distinguished from that of a pulley that moves with the car.

When reading a drawing, first examine what the pulleys are attached to, rather than their number. Following the rope anchorage points and the moving pulleys connected to the car makes the relationship between car travel and rope travel easier to understand.

In 2:1, rope speed can easily be mistaken for car speed

For conventional 2:1 Roping, the rope travels farther than the car. With the same Sheave rotational speed and effective diameter, car speed is calculated as half that under 1:1 conditions.

Conversely, to obtain the same car speed with the same effective diameter, the Sheave shaft rotational speed for 2:1 must be higher than for 1:1. If the Roping ratio changes, setting only the rotational speed to the same value will not produce the same car speed.

However, the notation 2:1 describes more than the speed relationship. The rope configuration supporting the car and the conditions of force transmission also change, so the speed formula alone cannot establish the suitability of a Traction Machine.

If the notation on a site drawing is unclear, do not guess the order of the numbers. Check both how the drawing defines the Roping ratio and the actual rope arrangement.

Comparing diameter and Roping notation in our Traction Machine listings

The Roping ratio can differ even with the same diameter

Our Traction Machine listings include MCK500 [Ø480] 1:1 and MCK500X [Ø480] 2:1. These entries show that the Roping conditions differ even though both specify Ø480.

The listings also include MCK500X [Ø520] 1:1 and MONA320 [Ø240] 2:1. Reading only the model name or only the diameter leaves out information needed to assess car speed.

The comparison below assumes that the listed diameter is the effective diameter for calculation and that all Sheave shaft rotational speeds are equal. It is a relative comparison, not a table of actual rated speeds or operating performance for each product.

Our listing notation Diameter and Roping conditions used in the comparison Calculated car speed relative to Ø480·1:1
MCK500 [Ø480] 1:1 480 ÷ 1 Same as the reference.
MCK500X [Ø480] 2:1 480 ÷ 2 Half the reference.
MCK500X [Ø520] 1:1 520 ÷ 1 520/480 times the reference.
MONA320 [Ø240] 2:1 240 ÷ 2 One-quarter of the reference.

What matters in this comparison is diameter divided by Roping ratio, rather than which model is superior. At the same rotational speed, an increase in this value produces a proportional increase in calculated car speed.

Distinguish listing notation from actual calculation inputs

The table above explains the speed relationship using the diameter numbers provided. The actual diameter basis represented by each product's notation must be checked separately in its drawings and technical documentation.

In particular, where different diameter and Roping combinations are listed, as with MCK500X, specifications must not be established from the model name alone. The complete combination, including diameter and Roping notation, must be compared.

Also distinguish between finding a candidate in a listing and reviewing its application on site. The former can begin with a comparison of notation, but the latter requires checking that the supplied specifications and actual installation also match.

Why the effective diameter for calculation must be checked separately

The visible outside diameter may not be the basis for rope travel

The Sheave has grooves in which the rope sits. Calculating rope travel requires a diameter corresponding to the path along which the rope actually moves, so measuring only the outside diameter at the Sheave's edge may be insufficient.

Nor can it be assumed that the diameter at the groove bottom can be used directly in the calculation. The rope's position within the groove and the design calculation basis must both be considered.

Technical documentation may contain dimensions with different meanings, such as nominal diameter, outside diameter and pitch circle diameter. Even when the terms are similar, interpret them according to the dimension lines and explanations in the relevant drawing.

The term effective diameter in this article is a functional expression for the diameter used in speed calculations. It must not automatically be treated as equivalent to a particular dimension name in product documentation.

Mixing dimensions with different reference bases undermines cause assessment

A difference between the listed diameter and a site measurement does not immediately indicate wear or incorrect assembly. First check whether the values refer to different measurement positions.

Conversely, the absence of a noticeable difference does not establish that motion is being transmitted normally. Rope and groove condition, slippage and related matters must be examined separately from the comparison of diameter notation.

It is advisable to record the source beside the diameter value on the calculation sheet. Distinguishing between a value taken from a drawing, a value confirmed by the manufacturer and a value measured at a specific position on site makes review easier.

If a change in groove condition is suspected, avoid inventing a corrected diameter to make the calculation fit. Keeping the design basis separate from condition inspection results preserves the grounds for explaining a speed discrepancy.

Read rotational speed together with the shaft and operating conditions

Distinguish motor shaft rotational speed from Sheave shaft rotational speed

The meaning of a rotational speed in the specifications depends on which shaft it describes. If there is a speed reduction relationship between the motor shaft and the Sheave shaft, the motor shaft rotational speed cannot be entered directly into the speed formula.

Convert motor shaft rotational speed to Sheave shaft rotational speed, then apply the effective Sheave diameter and Roping ratio. Omitting the speed reduction relationship changes the result even if the subsequent diameter and Roping calculations are correct.

Where the two shafts are directly connected, they can be regarded as having the same rotational relationship, but this must not be established from the product's appearance or name alone. Base the assessment on drawings and specifications describing the drive configuration.

When using a displayed rotational speed, check what the display represents. Whether it is a target value or an actual detected value affects how the calculation result is compared with car speed measured on site.

Do not treat rated values and instantaneous values as equivalent

Rated rotational speed is a specification for designated operating conditions. Actual operation includes acceleration and deceleration, so rotational speed is not equal to rated rotational speed at every moment.

To check the speed relationship, compare values from the same operating phase as far as possible. If Sheave rotational speed is read during constant-speed travel and car speed during deceleration, the two values are difficult to compare directly.

When recording a difference between calculated and measured values, also record the measurement location and timing. Recording load conditions and travel direction helps when comparing inspection results from different days.

A stable instrument display does not mean that the input conditions are also accurate. Check that the instrument was used correctly and that the measurement target was appropriate before examining mechanical causes.

On site, follow the sequence from document checks to measured-value comparison

First reconcile the sources of the specifications

Begin the inspection by identifying the model, but do not stop at the model name. Compare the nameplate, supplied specifications and installation drawings to check whether the diameter, Roping and rotational speed combinations match.

At sites with a history of replacement or modification, the current installation may differ from the original drawings. Check document dates and revision histories, and select documentation that describes the current condition.

Next, establish the calculation diameter and Sheave shaft rotational speed. If an unverified value is entered provisionally, mark it as an assumption and record which items must be replaced with confirmed values.

Check stage What to check Supporting information to record
Product identification Model name and diameter/Roping combination Nameplate and supplied specifications
Rope arrangement check Connections between anchorage points and moving pulleys Current installation drawings and site findings
Establish calculation inputs Effective diameter and Sheave shaft rotational speed Values and units in technical documentation
Speed relationship calculation Conversion between rope speed and car speed Formula used and assumed conditions
Measured-value comparison Rotational speed and car speed in the same operating phase Measurement method and operating conditions
Discrepancy review Inputs, measurement and motion transmission condition Findings and follow-up action

If there is a discrepancy, work back through the inputs first

If the calculated value differs from actual speed, first recheck the units and Roping ratio. Also check whether rope speed has been mistaken for car speed or motor shaft rotational speed has been used as the Sheave shaft value.

Then review the basis of the calculation diameter and the measurement conditions. Only after checking that the inputs and measurement method are correct can the condition of motion transmission between the rope and Sheave be examined as a cause.

Do not approach a moving rope or Sheave to check actual speed. The work must be performed by personnel with the required qualifications and authority, following site safety procedures and using appropriate measurement methods.

It is not appropriate to change the rotational speed setting first simply because the speed differs from expectations. Concealing a calculation error through adjustment leaves the cause unresolved and may affect other operating conditions.

Limits when using calculation results to judge replacement or modification

The same car speed does not mean the same drive conditions

Different combinations of diameter and Roping ratio can produce the same calculated car speed. This does not make the two Traction Machines interchangeable under the same conditions.

In addition to car speed, drive torque, rope configuration, Sheave grooves, loads acting on the shaft and braking conditions must be reviewed together. The speed formula does not describe all these conditions.

In particular, considering a larger diameter or a change in Roping ratio goes beyond a simple speed conversion. Relationships with surrounding components and the installation structure may change, so the overall application conditions must be checked.

Speed calculation is a tool for checking relationships between specifications. A final decision on product selection or modification requires both the technical documentation for the relevant Traction Machine and the site's design conditions.

Keep records that allow another person to repeat the calculation

Good records show the basis of the inputs more clearly than the resulting number alone. Bringing together the model name, diameter definition, shaft to which rotational speed refers and Roping ratio makes omitted conditions easier to identify during review.

Record calculated and measured values separately as well. Attach assumptions and units to calculated values, and measurement methods and operating conditions to measured values, so that the nature of the two sets of information remains distinct.

Leave unverified items marked as unverified rather than filling gaps with estimates. When contacting the manufacturer, it is also clearer to provide drawings and the dimensions requiring confirmation, rather than only the model name.

When communicating with building managers, distinguish confirmed facts from matters still requiring verification, rather than explaining every calculation formula. Explanations of speed relationships and judgments of operating suitability must be presented within the limits supported by the available evidence.

Car speed requires diameter, Roping and rotational speed to be read together

Even at the same Traction Machine rotational speed, car speed changes if the effective Sheave diameter or Roping ratio changes. Diameter determines rope travel, while the Roping ratio determines the relationship between rope travel and car travel.

The MCK500, MCK500X and MONA320 entries in our listings provide a starting point for comparing this relationship. Actual calculations require separate confirmation of the effective diameter and Sheave shaft rotational speed for the relevant specification.

On site, the sequence of checking specifications, calculating, comparing measured values and identifying the cause of discrepancies matters. Rebuild the calculation using confirmed conditions rather than interpreting site conditions to fit the calculation result.

Recording this process in maintenance records allows the next person responsible to make judgments on the same basis. The value of the speed formula lies both in obtaining numbers quickly and in reading different specifications on a common basis.

Frequently asked questions

Q1Does car speed vary with Sheave diameter and Roping ratio even at the same Traction Machine rotational speed?

Yes. At the same Sheave shaft rotational speed, a larger effective diameter increases rope speed. With the same effective diameter, car speed for conventional 2:1 Roping is calculated as half that for 1:1. Actual application requires checking the calculation diameter and rope arrangement.

Q2How should 1:1 and 2:1 be shown on a calculation sheet to make review easier?

Record both the Roping notation and the divisor used in the calculation. For example, for 2:1, write 'rope speed ÷ 2 = car speed' and keep the installation drawing used to confirm that relationship with the records.

Q3What information should be sent when asking the manufacturer about the calculation diameter?

It is advisable to provide the full model name, nameplate information, supplied specifications and Sheave drawing together. Specifically confirm whether the Ø notation in the listing is the diameter used for speed calculation or whether a different dimension must be used.

Q4If rotational speed is missing from the nameplate, can it be calculated back from car speed?

If the effective diameter and Roping ratio are confirmed, Sheave shaft rotational speed can theoretically be calculated back from car speed. However, that value is a result calculated under the given conditions and cannot replace documentation confirming the product's rated rotational speed.

Q5What should a building manager report if they notice a speed difference?

Tell the maintenance personnel when it occurred, the travel direction, whether it was during starting, constant-speed travel or arrival, and whether it repeats. Do not identify diameter or Roping as the cause based only on how the ride feels; have the personnel compare the specifications with measurement results.

Parts covered in this article

Products mentioned above, matched against our catalog.

Need to check whether it fits your site?

Tell us the model and site conditions — our team will confirm the specification and send a quote together with certificates and test reports.

Ask about MCK500 [Ø480] 1:1

Related articles

Growing together with our customers.

D&D

Get in touch


Contact us

Weekdays 09:00 to 18:00 KST

Call +82 31 983 6243Contact us